First On Net: How A Satellite Finder Works [with Pictures]

I Hunted Yasat-1 @ 52.5*East first time using this meter which I received on last year and Result are as follow with pictures:-

SATELLITE FINDER:-
[You must be registered and logged in to see this image.]

Now here find how to Connect the Sat finder Meter with LNB + STB with Pictures

You will see a Picture showing the Wires of LNB and STB are connected to Meter
showing One End to STB & Other End to LNB in Pictures.So connect your New Meter accordingly as shown friends.

SEE THE SS CONNECTING WIRES:-

IMAGE.1 TO LNB:-
[You must be registered and logged in to see this image.]

IMAGE.2 TO STB:-
[You must be registered and logged in to see this image.]

HERE BOTH STB & LNB CONNECTED:-
[You must be registered and logged in to see this image.]

THE LEDS INDICATIONS:-

A. LED marked with 22KHz: The receiver is sending a 22KHz signal, used to switch some LNB to the high band frequency.

B. LED marked with 0Hz: The receiver do not send the 22KHz signal.

C. LED marked with 13V: Indicates the satellite receiver is switching 13V power to switch the LNB's vertical polarization.

D. LED marked with 18V: Indicates the satellite receiver is switching 18V power to switch the LNB's horizontal polarization.
Above info. on the manual itself:
Pl share your Idea's,Experiences and suggestions about sat finder here so that all friends can be benefited.

Now Next Step is Before using do the following:-
1. Turn on the satellite receiver. It's scale should be lit at this time and the meter reading should be around 0.
2. Set your dish to the proper azimuth and elevation settings.
3. Set the Satellite Finder's scale reading to about 5 by adjusting the level control on the right side of the face of the Satellite Finder. (Turning the knob clockwise will increase the reading.)

You will see when we connect to the sat finder to stb then it get the supply from the stb and it start Glowing,
The second end of the sat finder give supply to LNB and after Receiving the signal the signal meter start moving Clock wise. Which show's how much signal we are receiving.

SEE THE SS OF WORKING THE SAT FINDER:-

The connection is made and we will start hunting satellite:
[You must be registered and logged in to see this image.]

Now as we get signal from any satellite the signal meter start moving:
[You must be registered and logged in to see this image.]

NOW NEXT:-

Dear friends When we get signal now the next step:
Here you will see two Images for Sat-finder KNOB which helps us to Reduce the scale-Reading or to adjust it,so you can see the ss with marking,This is KNOB to use when we get 20% to 30% signal and we can reduced it to Zero so that we can get full signal till the peak value show's full scale.thanks

HERE IS SS OF KNOB:-
[You must be registered and logged in to see this image.]

This knob has also a mazor Role in getting signal up to mark..

NOW NEXT STEP:-

Now after catching a satellite the signal start moving & increasing see the ss:

As the satellite signal increase, The signal on meter also Increase:
[You must be registered and logged in to see this image.]

Pl share your Experinces and also suggestions by commenting the Thread,thanks

Now The working of Various LEDS:-

Now the 13V, 18V LED to indicate the polarization: You can adjust the polarization to achieve optimum signal level for both polarizations. 0Hz, 22KHz LED: The 22KHz signal of the receiver is commonly used to switch LNB frequency between high and low band.

Now we get full signal of satellite and it also show's the VERTICAL POLARITY signal as show'n in the figure see the ss:
[You must be registered and logged in to see this image.]

Now we get full signal of satellite and it also show's the HORIZONTAL POLARITY signal as show'n in the figure see the ss:
[You must be registered and logged in to see this image.]

THE SAT FINDER ALSO SHOW"S 22K LED WHEN WE GET 22K SIGNAL FROM STB & VARIOUS POLARITIES SEE THE SS:
[You must be registered and logged in to see this image.]